Łatwy zwrot towaru
Promocja tego produktu! "Dostawa gratis na terenie całego kraju jeśli towar jest w naszym magazynie. Jeśli jest w magazynie obcym lub zagranicznym po zamówieniu magazyn wycenia transport"
"Większość towarów wysyłamy w ciągu 24h, po sprawdzeniu stanu magazynowego!"
Do godziny po zamówieniu (w godzinach pracy) magazynierzy sprawdzają czy zamówiony towar jest w magazynie i przesyłamy informację emailem lub SMS.
UWAGA: Dostawa 14 dni!
GermanTech jest wiodącym dostawcą produktów na bazie niemieckiej techniki i usług. W oparciu o ścisłą współpracę z niemieckimi producentami oraz o dokładną i kompleksową wiedzę na temat rynku, GermanTech jest w stanie zaoferować szeroką gamę niezawodnych produktów i rozwiązań biznesowych.
WÓZEK PALETOWY PODNOŚNIKOWY Z PRZECHYŁEM.
Kompaktowy wózek stabilnej konstrukcji z ergonomicznym nachylenia.Paleta jest podnoszona do właściwej wysokości roboczej i bokiem nachylenia sprawia, że praca wygodne i ergonomiczne. Dostępne w wersjach ręcznych i elektrycznych.Odchylenia to ręczne na obu typów.Konstrukcja jest bardzo zwarta i jest zatem odpowiednia do ciasnych przestrzeniach. Hamulce na obu kół.
Manual high lift truck with electric lifting (later "truck" only) is designed for the transport, handling and stacking of material which is placed on pallets. It enables to offtake and to base pallets to the maximum lifting height of the truck by using electrohydraulic aggregate. It decreases physical strain of person manipulating with material.
The truck consits from the outer frame, the internal frame, the working cylinder, the hydraulic aggregate, forks and the handle. The forks are lifted by chain anchored to the outer frame, which is pushed by a piston rod of the working cylinder. The opposite end of the chain is mounted to the forks. The offtaking of the piston rod is provided through the pressure of hydraulic oil created by hydraulic aggregate. The aggregate is activated by pressing of the push-button up and down. Wheels rotation angle is 360°, each of the wheel is equipped with a brake.
These parts are installed in the electric circuit:
- electric fuse for the power circuit
- electric fuse for the control circuit
- connector socket for connecting a charger
There is the throtting valve mounted within the hydraulic circuit.
Instructions to the truck usage
Oil check and filling
Truck´s working cylinder is filled with hydraulic oil RENOLIN HV - 32. If the truck is used daily, it is recommended to check oil level 1x a month. There is right amount of oil, if there is minimum amount of oil in the tank, while the forks are in the highest position. When filling hydraulic block with oil, it is necessary to filter it through 25 μm filter.
It is necessary to control battery regularly with an equipment for measuring of electrolyte density. It is recommended, when electrolyte density is below 75 % of nominal value, to recharge the battery, so it will be not depriciated. Clean and use the battery according to the battery´s instruction manual.
Always charge the battery by chargers, which refer to listed specification of required battery. A charger is delivered as extra.
Lowering speed adjusting
In hydraulic circle, on the plate of hydraulic cylinder there is a throtle valve assembled, by which the speed of forks lowering is set. In case, that it is necessary to change the speed of lowering, it is possible to order throtting valve with regulation screw on it (see the picture "Connecting and gripping of hydraulic unit EHS"), which can be used for speed changing.
This truck can be operated by a worker older than 18 years of age, who is mentally and physically suitable and knows all safety regulations regarding material handling using trucks with electric lifting and operation. Operation of the stacker is assured through two buttons.
Forks lifting is performed by using a press button where there is an "LIFT" arrow marked.This switches the electrohydraulic engine, which causes forks lifting.
When neither of the press buttons is pressed, the forks are in the neutral position. The load is held in any position, which is provided by a non-return valve in hydraulic circuit. Load transport is allowed when the forks are not higher then 200 mm above the floor.
By pressing the press-button where there is an "LOWER" arrow marked, the valve is opened and the forks are being lowered to their lowest position. Their lowering speed is regulated by the throttle valve.
When handling loads, operational procedures, which protect operators from accidents and injuries, must be used. These are mainly caused by incorrectly secured loads, by exceeding the max. load capacity, or by sliding of the truck on poor transport surfaces. Doorsills and other similar obstructions must be leveled by means of ramps as well as bridges between neighbouring floors.
It is forbidden:
• to use the truck for handling on inclined surfaces
• to perform any repairs and maintenance on a truck carrying a load
• to handle loads with a center of gravity higher than 500 mm
• to transport the loads while lifted higher than it is specified 200 mm over the ground except
technologically essential transport
• technologically essential transport isofftaking and placing of the load in the place of stacking.
It is necessary:
• to keep the loading diagram while manipulating with load, which is sticked on each stacker.
The user of product is after the end of technical life obligatory:
1. to drain the hydraulic system and to hand an oil over for recycling
2. to hand over all metal parts for recycling
3. to put all plastic parts into communal waste system